yastu: May be rfkill related
I enabled mobile broadband and it seems to be working (I haven't tried sending or receiving an SMS yet)
So I tried to undo it but it still reports it is registered with the network
So I used
rfkill block wwan
and it reports it can't register again with the network again.
rfkill unblock wwan
and it automatically connects.... modem is registered to the network
:oops:
|
yastu: I turned on debug mode this is the log:
There is a repeating section then the section below
It is receiving commands as I thought, but it says
"modem not registered"
I figure it is sending CREG=2
but the modemd doesn't respond with CREG? => 5
***************REPEAT START
2016-11-02 05:38:42,7, GSM1: -> AT+CSQ
2016-11-02 05:38:42,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:43,7, GSM1: <- +CSQ: 99,99 OK
2016-11-02 05:38:43,5, GSM1: Signal Strength Indicator: not present of not measurable, Bit Error Rate: not known or not detectable
2016-11-02 05:38:43,7, GSM1: -> AT+CREG?
2016-11-02 05:38:43,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:44,7, GSM1: <- +CREG: 2,0 OK
2016-11-02 05:38:44,5, GSM1: MODEM IS NOT REGISTERED, WAITING 1 SEC. BEFORE RETRYING 100. TIME
**************REPEAT END
2016-11-02 05:38:45,3, GSM1: Error: Modem is not registered to the network
2016-11-02 05:38:55,6, GSM1: Checking device for incoming SMS
2016-11-02 05:38:55,6, GSM1: Checking if modem is ready
2016-11-02 05:38:55,7, GSM1: -> AT
2016-11-02 05:38:55,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:55,7, GSM1: <- OK
2016-11-02 05:38:55,6, GSM1: Pre-initializing modem
2016-11-02 05:38:56,7, GSM1: -> ATE0+CMEE=1;+CREG=2
2016-11-02 05:38:56,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:56,7, GSM1: <- OK
2016-11-02 05:38:56,6, GSM1: Initializing modem
2016-11-02 05:38:57,7, GSM1: -> AT+CPMS="SM","SM","ME"
2016-11-02 05:38:57,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:57,7, GSM1: <- +CPMS: 0,30,0,30,1,30 OK
2016-11-02 05:38:58,7, GSM1: -> AT+CSQ
2016-11-02 05:38:58,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:58,7, GSM1: <- +CSQ: 99,99 OK
2016-11-02 05:38:58,6, GSM1: Signal Strength Indicator: not present of not measurable, Bit Error Rate: not known or not detectable
2016-11-02 05:38:58,6, GSM1: Checking if Modem is registered to the network
2016-11-02 05:38:59,7, GSM1: -> AT+CREG?
2016-11-02 05:38:59,7, GSM1: Command is sent, waiting for the answer
2016-11-02 05:38:59,7, GSM1: <- +CREG: 2,0 OK
2016-11-02 05:38:59,5, GSM1: MODEM IS NOT REGISTERED, WAITING 1 SEC. BEFORE RETRYING 1. TIME
|
yastu: Operating system name and version: Linux mint 15???
Version of smsd: no idea
Smsd installed from: package repository
Name and model of a modem / phone: ericsson hs2350
Interface: USB / ttyACM0 or 1
Hi
if I connect using cu -l /dev/ttyACM0
I can enter commands and it looks like it works
e.g. I entered AT+CPMS? and then AT+CPMS="SM","SM","ME" and it responds OK each time.
e.g.
AT+CPMS?
+CPMS: "SM",0,30,"SM",0,30,"ME",1,30
OK
But in the smstools logs all I get is this repeated ad infinitum:
2016-11-01 10:00:48,3, GSM1: write_to_modem: error 5: Input/output error
2016-11-01 10:00:58,3, GSM1: write_to_modem: error 5: Input/output error
2016-11-01 10:01:08,3, GSM1: Error: Unexpected answer from Modem after +CREG?, waiting 1 sec. before retrying
Since I can use cu, there shouldn't be an IO error?
I quit CU then restarted smstools, no change. (invoke-rc.d smstools restart)
Even if smstools is running cu works on the same port.....
smsd.conf, modem config part:
[GSM1]
init = AT+CPMS="SM","SM","ME"
device = /dev/ttyACM0
incoming = yes
sending_disabled = yes
rtscts = no (I tried yes and no difference)
baudrate = 19200
#baudrate = 115200
communication_delay = 5
NB cu works when forced to 19200 baud so I am pretty sure i got it right.
Any ideas???
|
