I have a problem when i send sms:
2017-08-11 11:00:23,6, GSM1: I have to send 1 short message for /var/spool/sms/checked/send_GIxQNq
2017-08-11 11:00:23,6, GSM1: Sending SMS from to 5215539001316
2017-08-11 11:00:23,6, GSM1: Checking if modem is ready
2017-08-11 11:00:23,7, GSM1: -> AT
2017-08-11 11:00:23,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:23,7, GSM1: <- OK
2017-08-11 11:00:23,6, GSM1: Pre-initializing modem
2017-08-11 11:00:24,7, GSM1: -> ATE0+CMEE=1;+CREG=2
2017-08-11 11:00:24,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:24,7, GSM1: <- OK +CREG: 1,"15FB","273D"
2017-08-11 11:00:24,7, GSM1: -> AT+CSQ
2017-08-11 11:00:24,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:24,7, GSM1: <- +CSQ: 15,0 OK
2017-08-11 11:00:24,6, GSM1: Signal Strength Indicator: (15,0) -83 dBm (Good), Bit Error Rate: less than 0.2 %
2017-08-11 11:00:24,6, GSM1: Checking if Modem is registered to the network
2017-08-11 11:00:25,7, GSM1: -> AT+CREG?
2017-08-11 11:00:25,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:25,7, GSM1: <- +CREG: 2,1,"15FB","273D" OK
2017-08-11 11:00:25,6, GSM1: Modem is registered to the network
2017-08-11 11:00:25,6, GSM1: Selecting PDU mode
2017-08-11 11:00:25,7, GSM1: -> AT+CMGF=0
2017-08-11 11:00:25,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:25,7, GSM1: <- OK
2017-08-11 11:00:26,7, GSM1: -> AT+CMGS=38
2017-08-11 11:00:26,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:26,7, GSM1: <- >
2017-08-11 11:00:26,7, GSM1: -> 0031000D91255135091013F60000FF1AC8329BFD0619E5E9B29B0C42BFEFA0B0BC0CAA83C4F237
2017-08-11 11:00:26,7, GSM1: Command is sent, waiting for the answer
2017-08-11 11:00:29,7, GSM1: <- +CMS ERROR: 21 (Short message transfer rejected)
2017-08-11 11:00:29,3, GSM1: The modem answer was not OK: +CMS ERROR: 21 (Short message transfer rejected)
2017-08-11 11:00:29,5, GSM1: Waiting 10 sec. before retrying
My conf is:
# Example smsd.conf. Read the manual for a description
devices = GSM1
logfile = /var/log/smsd/smsd.log
loglevel = 7
user = smstools
infofile = /var/run/smsd/smsd.working
pidfile = /var/run/smsd/smsd.pid
#sent = /var/spool/sms/sent
#outgoing = /var/spool/sms/sent
# 3.1.5 introduced smart logging
# once your configuration is OK, set log level lower (5 is good in most cases)
smart_logging = yes
[GSM1]
device = /dev/ttyUSB1
incoming = yes
report = yes
#pin = 1111
thank you for U help