|
|
SMS Server Tools 3 Community |
Welcome, Guest. The forum is currently read-only, but will open soon. |
Fri Feb 14, 2025 17:30 |
This topic is locked
Page: 1
Author |
Post |
|
#1 Mon Mar 01, 2010 11:34, 182 months ago.
|
Member
Registered: Feb 2010
Location: Raipur/Chattisgarh, India
|
Operating system name and version: Ubuntu 9.10- the Karmic Koala Version of smsd: 3.1.5 Smsd installed from: sources Name and model of a modem / phone: NOKIA 1110 Interface:USB (CA-45 datacable) Hi all, First of all thank you for developing this amazing product. I'm trying to develop an sms gateway for my college project, and i found sms server tools3. Initially i was using a S60 phone as modem, but later i came to know that i cant receive sms using that. i want to develop a two way messaging service for my project. Now i got one Nokia 1110 and want to set-up an sms gateway using that. I bought a CA-45 data cable too for the USB connectivity. my configuration and logfile are given below, i'm not sure whether the configuration is correct or not, but the port is working fine(/dev/ttyUSB0). smsd.config log please explain why these errors or special symbols are coming? and why am i not able to send or receive sms? Thank you.... 
|
|
#2 Mon Mar 01, 2010 12:25, 182 months ago.
|
Administrator
Registered: May 2009
Location: Jyväskylä, Finland
|
Have you already tried a lower baudrate, like 19200 or 9600?
You could use wvdialconf to detect your modem and baudrate, it also ensures that the cable is not broken.
Also, you could use some terminal program, like Minicom, to check if it can communicate with your device.
|
|
#3 Sun Mar 07, 2010 06:32, 181 months ago.
|
Member
Registered: Feb 2010
Location: Raipur/Chattisgarh, India
Topic owner
|
Thanks for the reply, the problem was the communication with my device. Now i brought a Samsung SGH E250 and i have some problem with sending SMS. I can receive SMS but when i try to send SMS some error occurs. The configuration and log are given below please give a solution. Thank You.
|
|
#4 Sun Mar 07, 2010 11:29, 181 months ago.
|
Administrator
Registered: May 2009
Location: Jyväskylä, Finland
|
I think you could try without the smsc setting.
Have you checked what is the smsc setting in the phone? Can you send SMS using your phone?
|
|
#5 Sun Mar 07, 2010 11:42, 181 months ago.
|
Member
Registered: Feb 2010
Location: Raipur/Chattisgarh, India
Topic owner
|
I tried without smsc setting the same error occurs. I have checked the smsc setting on the phone and it is same, and yes i can send SMS using my phone.
please help..
|
|
#6 Sun Mar 07, 2010 12:06, 181 months ago.
|
Administrator
Registered: May 2009
Location: Jyväskylä, Finland
|
Not sure, but probably this is a problem in communication. Use the modem settings:
init = ATE1+CMEE=1 pre_init = no
and try once again. After a PDU string is sent, it's echoed back and can be verified manually. If it's not the same, you have a bad cable or something like that.
|
|
#7 Sun Mar 07, 2010 12:24, 181 months ago.
|
Member
Registered: Feb 2010
Location: Raipur/Chattisgarh, India
Topic owner
|
I tried that settings, the log is given below. same error,  any other solution?? if i have a bad cable how can i receive SMS? there is no problem with receiving SMS
|
|
#8 Sun Mar 07, 2010 12:49, 181 months ago.
|
Administrator
Registered: May 2009
Location: Jyväskylä, Finland
|
This is going to be difficult...  The string is echoed back correctly which means that the cable is not bad. In some cases a bad cable can cause troubles when a long string is sent. At the same time receiving may work well. You could try without report = yes setting, if it has something to do with this failure. Also try with mode = old, but probably even this does not work. SGH E250I was reported as a working device, but some other Samsung phones did not work. The error has been the same, after a PDU is sent, nothing is received from the device and it's dead. Probably your phone just has a bad firmware and nothing can be done. 
|
|
#9 Sun Mar 07, 2010 15:00, 181 months ago.
|
Member
Registered: Feb 2010
Location: Raipur/Chattisgarh, India
Topic owner
|
I tried both settings but its not working. Anyway thanks for your reply, Now I'm using another device to send SMS. I have 1 more question. I want to reply automatically whenever the gateway receives a SMS. how to do that? I mean is there a way using PHP?? i'm using PHP and mysql. When the gateway get a SMS in a specific format, i want to filter out specific words from the SMS and search the database, then send the result to the user.
Do i have to write all code for this in shell script? (Inside the eventhandler?) or any other method like in PHP or something like that?
Please guide me..
Thank you.
« Last edit by keke on Sun Mar 07, 2010 15:56, 181 months ago. »
|
This topic is locked
Page: 1
Time in this board is UTC.
|
|
|
 |
|
 |
|