Operating system name and version: Raspbian wheezy
Version of smsd:: 3.1.14
Smsd installed from: sources
Name and model of a modem / phone: Nokia E65
Interface: USB

Hi,

everytime I start smsd via /etc/init.d/sms3 start it gets stuck at "Waiting for messages to send...":

2012-08-25 11:31:56,2, smsd: Smsd v3.1.14 started. 2012-08-25 11:31:56,2, smsd: Running as root:root. 2012-08-25 11:31:56,7, smsd: Running startup_check (shell): /var/spool/sms/incoming/smsd_script.W0QYhS /tmp/smsd_data.UclaL1 2012-08-25 11:31:56,7, smsd: Done: startup_check (shell), execution time 0 sec., status: 0 (0) 2012-08-25 11:31:56,4, smsd: File mode creation mask: 022 (0644, rw-r--r--). 2012-08-25 11:31:56,5, smsd: Outgoing file checker has started. PID: 2601. 2012-08-25 11:31:56,7, smsd: All PID's: 2601,2603 2012-08-25 11:31:56,5, GSM1: Modem handler 0 has started. PID: 2603. Will only send messages. 2012-08-25 11:31:56,6, GSM1: Checking if modem is ready 2012-08-25 11:31:57,7, GSM1: -> AT 2012-08-25 11:31:57,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:57,7, GSM1: <- OK 2012-08-25 11:31:57,6, GSM1: Pre-initializing modem 2012-08-25 11:31:57,7, GSM1: -> ATE0+CMEE=1;+CREG=2 2012-08-25 11:31:57,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:57,7, GSM1: <- OK 2012-08-25 11:31:57,6, GSM1: Checking if modem needs PIN 2012-08-25 11:31:57,7, GSM1: -> AT+CPIN? 2012-08-25 11:31:57,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:58,7, GSM1: <- +CPIN: READY OK 2012-08-25 11:31:58,7, GSM1: -> AT+CSQ 2012-08-25 11:31:58,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:58,7, GSM1: <- +CSQ: 10,99 OK 2012-08-25 11:31:58,6, GSM1: Signal Strength Indicator: (10,99) -93 dBm (Workable), Bit Error Rate: not known or not detectable 2012-08-25 11:31:58,6, GSM1: Checking if Modem is registered to the network 2012-08-25 11:31:58,7, GSM1: -> AT+CREG? 2012-08-25 11:31:58,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:59,7, GSM1: <- +CREG: 2,5,"000C","0C18" OK 2012-08-25 11:31:59,6, GSM1: Modem is registered to a roaming partner network 2012-08-25 11:31:59,6, GSM1: Location area code: 000C, Cell ID: 0C18 2012-08-25 11:31:59,7, GSM1: -> AT+CSQ 2012-08-25 11:31:59,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:59,7, GSM1: <- +CSQ: 10,99 OK 2012-08-25 11:31:59,6, GSM1: Signal Strength Indicator: (10,99) -93 dBm (Workable), Bit Error Rate: not known or not detectable 2012-08-25 11:31:59,6, GSM1: Selecting PDU mode 2012-08-25 11:31:59,7, GSM1: -> AT+CMGF=0 2012-08-25 11:31:59,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:31:59,7, GSM1: <- OK 2012-08-25 11:32:00,7, GSM1: -> AT+CIMI 2012-08-25 11:32:00,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:32:00,7, GSM1: <- 232116832295692 OK 2012-08-25 11:32:00,7, GSM1: -> AT+CGSN 2012-08-25 11:32:00,7, GSM1: Command is sent, waiting for the answer 2012-08-25 11:32:00,7, GSM1: <- 354832014646366 OK 2012-08-25 11:32:00,5, GSM1: CGSN: 354832014646366 2012-08-25 11:32:00,5, GSM1: IMSI: 232116832295692 2012-08-25 11:32:00,5, GSM1: Waiting for messages to send...

My config file:


Any suggestions?

Thanks in advance!

best regards,
felix

What you mean? This is not suppose to happen? If you send a message (put a valid file at /var/spool/sms/outgoing) the message are no sent?

This sounds very like when I informed a invalid number. I don't remember to see any warning, but the result was like "nothing happening".

I've got similar problem with raspbian. When I put a file to outgoing spool it disappears, but nothing happens.

Linux raspberrypi 3.2.27+ #285 PREEMPT Tue Nov 20 17:49:40 GMT 2012 armv6l GNU/Linux
Bus 001 Device 006: ID 12d1:1446 Huawei Technologies Co., Ltd. E1552/E1800/E173 (HSPA modem) //E150 really
Smstools 3.1.14-1.1

I think this is caused by a bug in smsd. Upgrade it to the 3.1.15.

It works, thank you!

Hi,

thanks for your reply. I also got it working with updating to 3.1.15.

best regards,
felix

EAD-01-103 MB ethernet adapter. & GSM Modem using smsd sending sms.. its keeps the smsfile at outgoing folder but not going to sms. then after server restarts all sms are gone...

.conf

devices = GSM1
logfile = /var/log/smsd.log
loglevel = 7
outgoing = /var/spool/sms/outgoing
checked = /var/spool/sms/checked

incoming = /var/spool/sms/incoming

delaytime = 10
errorsleeptime = 20
blocktime = 100
autosplit = 3
receive_before_send = no
[GSM1]
device = @ip:7727
incoming = yes
outgoing = yes
memory_start = 0
baudrate = 9600
report = yes
rtscts = yes
read_timeout = 60
init = AT
init2 = AT+CMGF=1

--

I am missing small changes .Can you please guide me to resolve this issues..

Advanced thanks

Ramesh