SMS Server Tools 3
This site is hosted by Kekekasvi.com
 Menu
Basic information:
Additional information:
Support:
Get SMS Server Tools 3:
Additional Options

 Sponsored links

 Search
Custom Search

 Visitor locations
 
 SMS Server Tools 3 Community
Welcome, Guest. Please login or register. Sun Feb 28, 2021 04:14
SMSTools3 Community » Help and support Bottom

[answered] CentOS 5.5 and USB Tri-band GPRS Modem

  This topic is locked

Page:  1

Author Post
Member
Registered:
Feb 2011
Location: United Kingdom
Operating system name and version: CentOS release 5.5
Version of smsd: 3.1.14
Smsd installed from: sources
Name and model of a modem / phone: USB Tri-band GPRS Modem - from deal extreme (benq m32)
Interface: USB

Okay, I have centos 5.5 with virtualmin installed. I inserted the usb modem and if i do - lsusb the modem is detected. However it is not creating a device file. there are no tty usb devices detected, i get this also if i plug in a usb mem stick.

Has anyone got any idea how to get this device detected properly... I have been trolling the web for 2 days and not having much success. I heard it may be something to do with (xen virtual passthrough??) I am not a linux expert so i'm a bit stuck. Any help appreciated.

Andy

Administrator
Registered:
May 2009
Location: Jyväskylä, Finland
First check the id's:

# sudo su
# /sbin/lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 067b:0609 Prolific Technology, Inc.
Bus 001 Device 001: ID 0000:0000

Then try:

# /sbin/modprobe -r usbserial
# /sbin/modprobe usbserial vendor=0x067b product=0x0609

Use dmesg to see what ttyUSB you now have.

To make this change permanent, you need to install usb_modeswitch and setup correct values for vendor and product. As I do not currently run CentOS, I cannot give detailed instructions for this.

By default, CentOS does not recognize BenQ M32, and situation is the same with many Huawei devices too. For example E1820 and E1552 are not recognized. With keywords "centos usb_modeswitch E1552" some instructions can be found. Also, www.centos.org Forum is a good place for CentOS specific questions.

Member
Registered:
Feb 2011
Location: United Kingdom
Topic owner
Keke
Thanks for the reply, sorry its been a while replying.

I can now see the deivce as ttyUSB0. When I try to send a text I get the following:



And so on.

Config file:

# Global configuration

devices = GSM1

loglevel = 7

logfile = /var/log/sms/smstools.log

outgoing = /var/spool/sms/outgoing
checked = /var/spool/sms/checked
failed = /var/spool/sms/failed
incoming = /var/spool/sms/incoming
sent = /var/spool/sms/sent

delaytime = 6
errorsleeptime = 12
blocktime = 180

autosplit = 3
receive_before_send = no

# Modem configuration

# Benq GSM

[GSM1]
device = /dev/ttyUSB0
init = AT+CNMI=0,0,0,1,0
incoming = yes
check_memory_method = 31
phonecalls = clip
voicecall_hangup_ath = yes
voicecall_cpas = yes
needs_wakeup_at = yes
using_routed_status_report = yes
routed_status_report_cnma = no
 
'smsdconf' Syntax Highlight powered by GeSHi




Any help please

Regards

Administrator
Registered:
May 2009
Location: Jyväskylä, Finland
/dev/ttyUSB0 does not work properly. Did you install usb_modeswitch, or did you just use the modprobe?

But in any case, I think that I'm unable to help you :(. You will get better and faster help from here: www.centos.org Forum.

  This topic is locked

Page:  1

SMSTools3 Community » Help and support Top

 
Time in this board is UTC.  

Privacy Policy   SMS Server Tools 3 Copyright © Keijo Kasvi.