SMSTools3 Help and support

Welcome, Guest. The forum is currently read-only, but will open soon.

Thu Nov 21, 2024 22:35

• SMSTools3 Community » Help and support

[solved] can receive but not send messages

This topic is locked

Page: 1

Author	Post
crub	Bottom #1 Thu May 05, 2011 12:18, 164 months ago.
Member Registered: May 2011 Posts: 3 Location: germany, Germany	Operating system name and version: SLES 9 Version of smsd: 3.1.14 Smsd installed from: sources Name and model of a modem / phone: SE W800i Interface: serial/usb: /dev/ttyACM1 I can receive sms: 2011-05-05 14:07:38,6, GSM1: Checking device for incoming SMS 2011-05-05 14:07:38,6, GSM1: Checking if modem is ready 2011-05-05 14:07:38,7, GSM1: -> AT 2011-05-05 14:07:38,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:39,7, GSM1: <- OK 2011-05-05 14:07:39,6, GSM1: Pre-initializing modem 2011-05-05 14:07:39,7, GSM1: -> ATE0+CMEE=1;+CREG=2 2011-05-05 14:07:39,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:39,7, GSM1: <- OK 2011-05-05 14:07:39,6, GSM1: Initializing modem 2011-05-05 14:07:39,7, GSM1: -> AT+CPMS="ME" 2011-05-05 14:07:39,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:40,7, GSM1: <- +CPMS: 0,195,0,15,0,195 OK 2011-05-05 14:07:40,7, GSM1: -> AT+CSQ 2011-05-05 14:07:40,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:40,7, GSM1: <- +CSQ: 25,0 OK 2011-05-05 14:07:40,6, GSM1: Signal Strength Indicator: (25,0) -63 dBm (Excellent), Bit Error Rate: less than 0.2 % 2011-05-05 14:07:40,6, GSM1: Checking if Modem is registered to the network 2011-05-05 14:07:40,7, GSM1: -> AT+CREG? 2011-05-05 14:07:40,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:41,7, GSM1: <- +CREG: 2,1,"3D44","0000A5C4" OK 2011-05-05 14:07:41,6, GSM1: Modem is registered to the network 2011-05-05 14:07:41,6, GSM1: Selecting PDU mode 2011-05-05 14:07:41,7, GSM1: -> AT+CMGF=0 2011-05-05 14:07:41,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:41,7, GSM1: <- OK 2011-05-05 14:07:41,6, GSM1: Checking memory size 2011-05-05 14:07:41,7, GSM1: -> AT+CPMS? 2011-05-05 14:07:41,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:42,7, GSM1: <- +CPMS: "ME",1,195,"SM",0,15,"ME",1,195 OK 2011-05-05 14:07:42,6, GSM1: Used memory is 1 of 195 2011-05-05 14:07:42,6, GSM1: Trying to get stored message 1 2011-05-05 14:07:42,7, GSM1: -> AT+CMGR=1 2011-05-05 14:07:42,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:42,7, GSM1: <- +CMGR: 0,,24 0xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxE OK 2011-05-05 14:07:42,5, GSM1: SMS received, From: 49151xxxxxxxxx 2011-05-05 14:07:42,6, GSM1: Wrote an incoming message file: /var/spool/sms/incoming/GSM1.RDMBGf 2011-05-05 14:07:42,6, GSM1: Deleting message 1 2011-05-05 14:07:42,7, GSM1: -> AT+CMGD=1 2011-05-05 14:07:42,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:43,7, GSM1: <- OK 2011-05-05 14:07:43,6, GSM1: Checking device for incoming SMS 2011-05-05 14:07:43,6, GSM1: Checking memory size 2011-05-05 14:07:43,7, GSM1: -> AT+CPMS? 2011-05-05 14:07:43,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:07:43,7, GSM1: <- +CPMS: "ME",0,195,"SM",0,15,"ME",0,195 OK 2011-05-05 14:07:43,6, GSM1: Used memory is 0 of 195 2011-05-05 14:07:43,6, GSM1: No SMS received [ Select ] [ Expand ] but i cant send, maybe because no ctrl-z is sent after the pdu - how can i have sent an ctrl-z after the pdu? 2011-05-05 14:11:53,5, smsd: Moved file /var/spool/sms/outgoing/send_Z23898 to /var/spool/sms/OTHER 2011-05-05 14:11:54,6, GSM1: I have to send 1 short message for /var/spool/sms/OTHER/send_Z23898 2011-05-05 14:11:54,6, GSM1: Sending SMS from to 015121xxxxxx 2011-05-05 14:11:54,6, GSM1: Checking if modem is ready 2011-05-05 14:11:55,7, GSM1: -> AT 2011-05-05 14:11:55,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:55,7, GSM1: <- OK 2011-05-05 14:11:55,6, GSM1: Pre-initializing modem 2011-05-05 14:11:55,7, GSM1: -> ATE0+CMEE=1;+CREG=2 2011-05-05 14:11:55,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:55,7, GSM1: <- OK 2011-05-05 14:11:55,6, GSM1: Initializing modem 2011-05-05 14:11:56,7, GSM1: -> AT+CPMS="ME" 2011-05-05 14:11:56,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:56,7, GSM1: <- +CPMS: 0,195,0,15,0,195 OK 2011-05-05 14:11:56,7, GSM1: -> AT+CSQ 2011-05-05 14:11:56,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:56,7, GSM1: <- +CSQ: 27,99 OK 2011-05-05 14:11:56,6, GSM1: Signal Strength Indicator: (27,99) -59 dBm (Excellent), Bit Error Rate: not known or not detectable 2011-05-05 14:11:56,6, GSM1: Checking if Modem is registered to the network 2011-05-05 14:11:57,7, GSM1: -> AT+CREG? 2011-05-05 14:11:57,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:57,7, GSM1: <- +CREG: 2,1,"3D44","0000A5C4" OK 2011-05-05 14:11:57,6, GSM1: Modem is registered to the network 2011-05-05 14:11:57,6, GSM1: Selecting PDU mode 2011-05-05 14:11:57,7, GSM1: -> AT+CMGF=0 2011-05-05 14:11:57,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:58,7, GSM1: <- OK 2011-05-05 14:11:58,7, GSM1: -> ATE1+CMGS=15 2011-05-05 14:11:58,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:11:58,7, GSM1: <- > 2011-05-05 14:11:58,7, GSM1: -> 00xxxxxxxxxxxxxxxxxxxxx0000FF0131 2011-05-05 14:11:58,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:12:20,7, GSM1: <- 00xxxxxxxxxxxxxxxxxxxxx0000FF0131 +CMS ERROR: 500 (Unknown error) 2011-05-05 14:12:20,5, GSM1: Verify PDU: OK 2011-05-05 14:12:20,7, GSM1: -> ATE0 2011-05-05 14:12:20,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:12:21,7, GSM1: <- ATE0 OK 2011-05-05 14:12:21,3, GSM1: The modem answer was not OK: 00xxxxxxxxxxxxxxxxxxxxx0000FF0131+CMS ERROR: 500 (Unknown error) 2011-05-05 14:12:21,5, GSM1: Waiting 30 sec. before retrying [ Select ] [ Expand ] my config: devices = GSM1 outgoing = /var/spool/sms/outgoing checked = /var/spool/sms/checked incoming = /var/spool/sms/incoming loglevel = 7 #alarmhandler = /usr/local/bin/alarmevent alarmlevel = 4 delaytime = 20 errorsleeptime = 30 blocktime = 3600 receive_before_send = no # autosplit 0=no 1=yes 2=with text numbers 3=concatenated autosplit = 3 [queues] OTHER = /var/spool/sms/OTHER [provider] OTHER = 0,1,2,3,4,5,6,7,8,9 [GSM1] init = AT+CPMS="ME" device = /dev/ttyACM1 incoming = yes queues = OTHER mode = new baudrate = 19200 rtscts = yes cs_convert = no report = no memory_start = 1 #message_count_clear = 60 verify_pdu=yes [ Select ] [ Expand ] 'smsdconf' Syntax Highlight powered by GeSHi Any idea? Thanks for your help chris
keke	Top #2 Thu May 05, 2011 12:41, 164 months ago.
Administrator Registered: May 2009 Posts: 2070 Location: Jyväskylä, Finland	The sending fails, because the number is presented in national format. Change it to 49151xxxx. There are settings available to handle number formats, but in usual cases international format is the best choice. See SMS file format, "To_TOA" and "Using Type Of Address selection". Ctrl-Z is sent after the PDU, but your log (editor) just does not show it. You have disabled cs_convert for some reason. When it is disabled, outgoing messages should be written using GSM alphabet instead of latin1, and incoming messages will be in GSM alphabet too. Is this what you really have meant?
crub	Top #3 Thu May 05, 2011 13:02, 164 months ago.
Member Registered: May 2011 Posts: 3 Location: germany, Germany Topic owner	hello ke ke, thank you very much for the fast answer i tried 49151.... but unfortunately same result :-( 2011-05-05 14:55:05,5, smsd: Moved file /var/spool/sms/outgoing/send_m10522 to /var/spool/sms/OTHER 2011-05-05 14:55:06,6, GSM1: I have to send 1 short message for /var/spool/sms/OTHER/send_m10522 2011-05-05 14:55:06,6, GSM1: Sending SMS from to 49151xxxxxxxx 2011-05-05 14:55:06,6, GSM1: Checking if modem is ready 2011-05-05 14:55:06,7, GSM1: -> AT 2011-05-05 14:55:06,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:06,7, GSM1: <- OK 2011-05-05 14:55:06,6, GSM1: Pre-initializing modem 2011-05-05 14:55:06,7, GSM1: -> ATE0+CMEE=1;+CREG=2 2011-05-05 14:55:06,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:07,7, GSM1: <- OK 2011-05-05 14:55:07,6, GSM1: Initializing modem 2011-05-05 14:55:07,7, GSM1: -> AT+CPMS="ME" 2011-05-05 14:55:07,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:07,7, GSM1: <- +CPMS: 0,195,0,15,0,195 OK 2011-05-05 14:55:08,7, GSM1: -> AT+CSQ 2011-05-05 14:55:08,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:08,7, GSM1: <- +CSQ: 27,99 OK 2011-05-05 14:55:08,6, GSM1: Signal Strength Indicator: (27,99) -59 dBm (Excellent), Bit Error Rate: not known or not detectable 2011-05-05 14:55:08,6, GSM1: Checking if Modem is registered to the network 2011-05-05 14:55:08,7, GSM1: -> AT+CREG? 2011-05-05 14:55:08,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:08,7, GSM1: <- +CREG: 2,1,"3D44","0000A5C4" OK 2011-05-05 14:55:08,6, GSM1: Modem is registered to the network 2011-05-05 14:55:08,6, GSM1: Selecting PDU mode 2011-05-05 14:55:09,7, GSM1: -> AT+CMGF=0 2011-05-05 14:55:09,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:09,7, GSM1: <- OK 2011-05-05 14:55:09,7, GSM1: -> ATE1+CMGS=16 2011-05-05 14:55:09,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:09,7, GSM1: <- > 2011-05-05 14:55:10,7, GSM1: -> 00xxxxxxxxxxxxxxxxxxxxxF90000FF0131 2011-05-05 14:55:10,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:31,7, GSM1: <- 00xxxxxxxxxxxxxxxxxxxxxF90000FF0131 +CMS ERROR: 500 (Unknown error) 2011-05-05 14:55:31,5, GSM1: Verify PDU: OK 2011-05-05 14:55:31,7, GSM1: -> ATE0 2011-05-05 14:55:31,7, GSM1: Command is sent, waiting for the answer 2011-05-05 14:55:31,7, GSM1: <- ATE0 OK 2011-05-05 14:55:31,3, GSM1: The modem answer was not OK: 00xxxxxxxxxxxxxxxxxxxxxF90000FF0131+CMS ERROR: 500 (Unknown error) 2011-05-05 14:55:31,5, GSM1: Waiting 30 sec. before retrying [ Select ] [ Expand ] cs_convert was changed in hope to help - i tired many things, but did never succeed in sending. now i have set cs_convert to yes again. my first idea was an incomplete init string - an tried also there several options - without success...
keke	Top #4 Thu May 05, 2011 13:09, 164 months ago.
Administrator Registered: May 2009 Posts: 2070 Location: Jyväskylä, Finland	Have you verified this SIM in your handset? I assume that sending with it works. You could then check what is the number of Service Center (SMSC). Add a modem setting: smsc = <number in international format without the + sign>. Restart smsd and try once again.
crub	Top #5 Thu May 05, 2011 14:06, 164 months ago.
Member Registered: May 2011 Posts: 3 Location: germany, Germany Topic owner	Helo keke that was in deed the problem. an wrong service-center. i put in the correct one and it worked fine! thx! Great tool!

This topic is locked

Page: 1

• SMSTools3 Community » Help and support

Top

Time in this board is UTC.